混凝土自上料攪拌車進工地時注意觀察幾點
混凝土攪拌車是“一站三車”的重要組成設備之一，承擔著將商品混凝土從攪拌站、可靠、的運輸?shù)浇ㄔO(shè)工地的任務。那么混凝土自上料攪拌車進工地時注意觀察幾點呢？下面混凝土自上料攪拌車廠家為您分析：
Concrete mixer truck is one of the important components of the "one station, three vehicles" equipment, responsible for the safe, reliable, and efficient transportation of commercial concrete from the mixing station to the construction site. So what should be observed when the concrete self loading mixer truck enters the construction site? The manufacturer of the concrete self loading mixer truck will analyze for you:
1、攪拌車進工地時行駛在路中間
1. The mixing truck is driving in the middle of the road when entering the construction site
一般工地道路簡易，路基比較松軟，靠近路邊，容易被壓塌方了，導致車輛側翻。
Generally, the roads on construction sites are simple, and the roadbed is relatively soft. Near the roadside, it is easy to collapse and cause vehicles to roll over.
2、提前下車查看倒車線路
2. Get off the car in advance and check the reversing route
工地一般工況復雜，倒車時下車?yán)@車一周，查看倒車路線，注意躲避障礙物和坑洼，清理遇到的鋼筋釘子。
The general working conditions of the construction site are complex. When reversing, get off the car and take a detour around the car. Check the reversing route, pay attention to avoiding obstacles and potholes, and clean up any steel nails encountered.
3、倒車要慢
3. Reverse slowly
別總是把頭伸出窗外，要看著兩邊后視鏡一起兼顧，實在不確定就停車看清楚再倒。用一檔起步倒車，緩慢而勻速的行駛，好多路面是挖掘機剛剛鋪的比較軟，車容易陷入。
Don't always stick your head out of the window. Look at both rearview mirrors and consider them together. If you're unsure, stop and look clearly before reversing. Starting from first gear and reversing at a slow and uniform speed, many roads have just been paved with soft excavators, making it easy for the car to get stuck.
4、行車要慢
4. Drive slowly
攪拌車高，高速行駛?cè)菀装l(fā)生事故。入彎之前提前減速減擋，盡量別在拐彎的時候踩剎車。隨時注意觀察攪拌罐是否在轉，把轉速盡量調慢，轉速過高，車輛產生擺動，出現側翻。攪拌車在傾斜角大的路段需要停下罐。滿載料時走到傾斜角度大的路段，停止罐體的轉動可以使車輛行駛的更加平穩。
The center of gravity of the mixer truck is high, and high-speed driving is prone to accidents. Slow down and downshift before entering the corner, and try not to apply the brake when turning. Always pay attention to whether the mixing tank is rotating, and try to slow down the speed as much as possible. If the speed is too high, the vehicle will sway and roll over. The mixing truck needs to stop the tank on a section with a large inclination angle. When fully loaded, walking to a section with a large inclination angle and stopping the rotation of the tank can make the vehicle travel more smoothly.
遇到路面不平，坑坑洼洼地方用合適的低速擋通過，保證車隨時有爆發力。注意避讓雜物。起步要平穩，不能亂減檔，提前減檔，保持車輛充足的動力。
When encountering uneven road surfaces or potholes, use a suitable low-speed gear to pass through, ensuring that the car has explosive power at any time. Be careful to avoid debris. Start smoothly, do not downshift randomly, downshift early, and maintain sufficient power of the vehicle.
長時間行駛或者下坡前都要習慣的測試一下剎車。禁止攪拌車空擋滑行下坡，采用低檔位發動機減速，下坡路段出現彎路，要在拐彎時提前減速再減擋再減速，帶擋剎車效果好。運輸前提前規劃好路線，注意限高，工地路況復雜，要小心樹木，要防止刮到線纜。
Be accustomed to testing the brakes before driving for a long time or downhill. It is prohibited for the mixer truck to slide downhill in neutral. Low gear engines should be used to slow down. If there are bends in the downhill section, it is necessary to slow down in advance and then downshift before decelerating. The braking effect with gear is good. Plan the route in advance before transportation, pay attention to height restrictions, and be careful of the complex road conditions on the construction site. Be careful of trees and prevent scratching the cables.
此外非操作人員，禁止操作。下班后，必須將整車及進料斗、攪拌筒內外、出料溜槽等清洗干凈。把車門鎖好，轉動鎖緊手柄，鎖牢油門手柄和伺服手柄。更多相關內容就來我們網站http://www.zvmc.cn咨詢！
In addition, non operators are prohibited from operating. After work, the entire vehicle, feed hopper, mixing drum, discharge chute, etc. must be cleaned thoroughly. Lock the car, turn the locking handle, lock the throttle handle and servo handle securely. For more related content, come to our website http://www.zvmc.cn consulting service
