中科攪拌機出現抱軸情況的原因分析！
你知道中科攪拌機在工作時為什么會出現抱軸情況嗎？因在整個攪拌期間，粉料、砂石、液體混合所形成的粘結物，黏附在攪拌軸、攪拌臂上，經過長時間的積累，機械內部表面就會形成一層厚實且不易清理的粘結物。
Do you know why the shaft holding occurs when the mixer is working? During the whole mixing period, the binder formed by mixing powder, sand and liquid adheres to the mixing shaft and mixing arm. After a long time of accumulation, a thick and hard to clean adhesive will be formed on the internal surface of the machine.
影響混凝土質量，當機械在運行時出現抱軸后，就會打出不均勻的混凝土。
Affect the quality of concrete, when the machine is in operation, the uneven concrete will be produced.
增加機械負載，增加能耗。
Increase mechanical load and energy consumption.
影響耐磨件、軸端密封的使用壽命，加快耐磨件的磨損速度。發生抱軸后，攪拌臂也會磨損得非常嚴重，使用壽命也會明顯縮短。
The service life of wear-resistant parts and shaft end seals is affected, and the wear rate of wear-resistant parts is accelerated. After axle holding, the mixing arm will be seriously worn and its service life will be significantly shortened.
對進料順序、進料時間進行有效調整，骨料、粉料預混落入主機內（骨料須先下一部分），這樣可讓粉料在一定程度上附著在骨料上，減輕粉料落入主機內附著在攪拌軸、臂上的可能性降低，并且還可提高攪拌效率。
The feeding sequence and feeding time are effectively adjusted, and the premixed aggregate and powder fall into the host machine (the aggregate must be the next part first), which can make the powder adhere to the aggregate to a certain extent, reduce the possibility of powder falling into the host and adhere to the mixing shaft and arm, and improve the mixing efficiency.
主機蓋水管線要求與攪拌軸線處于同一垂直面上，同時還應保證攪拌臂與攪拌軸夾角位置上方有直噴噴嘴。因攪拌臂、軸夾角位置是粘結物容易附著的地方，一般出現抱軸都是從攪拌臂根部開始，同時還要求加水時間貫穿始終。
The center line of the water pipe on the cover of the main engine should be in the same vertical plane as the center line of the mixing shaft. At the same time, it should be ensured that there is a direct injection nozzle above the angle between the mixing arm and the mixing shaft. Because the angle between the mixing arm and the shaft is the place where the adhesive is easy to adhere, the shaft holding usually starts from the root of the mixing arm, and at the same time, it is required to add water through the whole process.
隨著工程項目的不斷推進，與工程項目密切相關的攪拌設備使用次數也會隨之加多，而它作為攪拌設備的“心臟”，提升機械設計、使用科學性具有關重要的作用。
With the continuous progress of engineering projects, the use of mixing equipment closely related to engineering projects will also increase. As the "heart" of mixing equipment, it plays an important role in improving mechanical design and scientific use.
