避免自上料攪拌車輪胎的過度損害具體做法
隨著攪拌車成本的持續提升，逼迫著人們不放過任何一個節省支出的細節。攪拌車輪胎其實是使用過程中頗占成本的一項耗材，盡量避免輪胎的過度損害就要先了解損害有怎樣的表現，然后再來看處理方法。
With the continuous increase in the cost of mixer trucks, people are forced to spare no details of cost savings. In fact, the mixer tire is a consumable that accounts for a lot of costs in the use process. To avoid excessive damage to the tire as far as possible, we should first understand the performance of the damage, and then look at the treatment methods.
轉向輪輪胎胎面或兩邊不正常磨損。檢查胎壓是否過低或輪胎質量是否過關。不要貪圖便宜使用三無輪胎。輪胎的鋼圈是否失圓，做個動平衡。檢查前束尺寸、轉向拉桿球頭是否松曠，方向機固定螺絲有沒有松動。轉向橋主軸或壓力軸承是否磨損嚴重變形或損壞。
Abnormal wear on the tread or both sides of the steering wheel tire. Check whether the tire pressure is too low or whether the tire quality is qualified. Don't use three no tires for cheap. Whether the steel ring of the tire is out of round, make a dynamic balance. Check the toe in size, whether the steering rod ball joint is loose, and whether the steering gear fixing screw is loose. Whether the steering axle main shaft or pressure bearing is worn, severely deformed or damaged.
后輪輪胎胎面呈不規則型磨損。檢查鋼圈，輪轂螺絲及軸頭螺絲是否松動。檢查剎車轂是否失圓。彈簧板和弓卡固定螺絲是否有松動。日常勤檢查輪胎氣壓，要看看輪胎胎面的磨損情況。早發現早修理，把損失降到低限度。
The tread of the rear tires is worn irregularly. Check whether the steel ring, hub screw and shaft head screw are loose. Check whether the brake hub is out of round. Check whether the fixing screws of spring plate and bow clamp are loose. Check the tire pressure frequently every day to see the wear of the tire tread. Find and repair early, and reduce the loss to a minimum.
輪胎部分的早期磨損。適當提高輪胎充氣量，可以減小輪胎與路面的接觸面積，從而減小輪胎的滾動阻力，節約燃油。但充氣量過大時，不但影響輪胎的減振性能，還會使輪胎變形量過大，與地面的接觸面積太小，磨損只能由胎面部分承擔，形成早期磨損。
Early wear of the central part of the tire. Properly increasing the inflation of the tire can reduce the contact area between the tire and the road, so as to reduce the rolling resistance of the tire and save fuel. However, when the inflation volume is too large, it will not only affect the vibration damping performance of the tire, but also make the tire deformation too large, and the contact area with the ground is too small. The wear can only be borne by the central part of the tread, forming early wear.
此外自上料攪拌車廠家提醒各位司機應避免原地打方向，而應該在輪胎滾動時打方向，這樣的話，地面給攪拌車輪胎帶來的才是且均勻的正常磨損。由于車感不佳，很多新手都喜歡原地打方向，這個壞習慣基本上是從駕校里面帶出來的。原地打方向會令輪胎的磨損集中在同一個接觸面上，造成輪胎局部嚴重磨損，縮短使用壽命。
In addition, since the charging mixer truck manufacturer reminds all drivers to avoid turning the direction in situ, and should turn the direction when the tire rolls. In this way, the ground will bring all-round and uniform normal wear to the mixer truck tire. Due to the poor feeling of the car, many novices like to steer in place. This bad habit is basically brought out from the driving school. Turning the direction in place will make the wear of the tire concentrated on the same contact surface, causing serious local wear of the tire and shortening the service life.
以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都?xì)g迎關注我們網站http://www.zvmc.cn并咨詢我們的工作人員，將竭誠為您服務。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.zvmc.cn And consult our staff, will serve you wholeheartedly.
